Clermont Aluminum Mini Blinds From Clermont Window Treatments

A workshop window has had nothing on it for years

A metal stud wall pulled the old brackets right out

A small office needs matching blinds throughout

Sidelight glass is too shallow for a wide slat

Kinks show at the route holes down the middle

Utility room glare lands right on a work bench

The cord lock slips and the blind drops on its own

Slats are creased where a pet pushed through them

Cut-down blinds bind at one end of the opening

Blinds rattle every time the air comes on

Every opening measured on its own and cut to size at the factory, never trimmed down from a stock blind on a truck

Three widths taken per opening so the narrowest one governs the order, because a mini blind binds fast if it's cut long

Corner-to-corner square check on every opening, including the utility ones nobody looks at twice

Slat gauge specified, the heavier gauge where a blind gets handled daily and the lighter one where cost governs

Slat size set per opening, 1 inch as the standard, 1/2 inch on shallow openings and sidelights, 2 inch where a wider face suits

Mounting depth read so a 1 inch headrail clears any handle, lock or crank inside the opening

Inside or outside mount decided opening by opening rather than once for a whole building

Cordless lift specified in units children use and offered as the default on rental turnovers

Products specified to conform to ANSI/WCMA A100.1-2022 for cord access

Cord tilt or wand tilt chosen against what the room actually needs rather than what's cheapest

Bracket substrate identified before install day: drywall, plaster, hardwood trim, block or steel

Color matched across a run so a whole building reads the same from the parking lot

Unit counts and finished sizes listed per opening on the paperwork so a single blind can be reordered later

Valance clips counted and checked, since a snapped clip is the usual reason a valance sits crooked

Light gap per side disclosed even on the least expensive units in the order

Old blinds removed, brackets pulled and the hardware hauled off rather than left in a bag

Every blind tilted through full travel and raised to the headrail before sign-off

Exact color and slat size written down for the owner where a building is getting a run of them

1 inch aluminum slat: The standard mini blind and the reason the category exists. A thin slat stacks to almost nothing at the top, fits shallow openings other products can't, and costs less than anything else that still counts as a real window covering.

1/2 inch micro slat: Half the slat width, so the stack is tiny and the blind almost disappears when raised. It's the answer on a shallow opening, a narrow sidelight beside a door, or a small commercial opening where a 1 inch headrail won't clear.

2 inch aluminum slat: A wider aluminum slat that reads more like a blind and less like a utility fitting. It gives better view when tilted open and covers more per slat. Choose it where the budget is tight but the room is still one people sit in.

Heavier gauge slat: Thicker aluminum that resists a crease and springs back from a knock that would permanently fold a thin slat. It costs a little more per unit. On any opening people reach through daily, that difference pays back within the first year.

Lighter gauge slat: The thinner, less expensive slat. It's honest value on openings that get looked at rather than handled, like a high utility window or a stairwell landing, and it's the wrong pick anywhere a hand is going in every day.

Cord tilt: A short cord loop beside the headrail that turns the tilt. It's the traditional control, it costs nothing extra, and it's the one to avoid where a child could reach it or a door swing keeps catching the loop.

Wand tilt: A rigid wand instead of a hanging tilt cord. Nothing loops, nothing swings into a door, and it's what we specify on any unit where a cord shouldn't be present at all. On mini blinds it adds very little to the price.

Cordless lift: No lift cord on the blind, with a spring mechanism doing the work in the headrail. On a light aluminum blind cordless feels particularly good, and it's the specification we push on rentals where you can't control who lives there next.

Perforated slats: Slats punched with a fine pattern so some daylight passes even when the blind is closed. It's a light-and-privacy compromise you occasionally want in a commercial corridor or a stairwell, where full darkness is the wrong outcome.

Hold-down brackets: Small brackets at the bottom rail that pin the blind to the frame. They stop a blind swinging every time a door opens, which is why they belong on any opening set into a door and on windows near a busy walkway.